{"id":9235,"date":"2025-01-06T10:31:52","date_gmt":"2025-01-06T02:31:52","guid":{"rendered":"https:\/\/www.textile-fabric.com\/archives\/9235"},"modified":"2025-01-06T10:31:52","modified_gmt":"2025-01-06T02:31:52","slug":"a-simple-memory-method-for-american-standard-fabric-scores-2","status":"publish","type":"post","link":"https:\/\/www.textile-fabric.com\/?p=9235","title":{"rendered":"A simple memory method for American Standard fabric scores!"},"content":{"rendered":"
\nAmerican standard inspection and width calculation of gray fabric<\/span><\/strong><\/section>\n<\/p>\n

1)<\/span>Test each piece of cloth at least three times. <\/span><\/span><\/p>\n

2)<\/span>If the width cannot meet the processing requirements, it will be considered unqualified.<\/span><\/span><\/span><\/p>\n

3)<\/span>Full width: the distance between two cloth edges.<\/span><\/span><\/span><\/p>\n

4)<\/span>Effective width: remove selvage, Width of pinhole and non-printed parts <\/span><\/span><\/p>\n<\/p>\n

\nSpecific provisions of the American four-point scale<\/span><\/strong><\/section>\n<\/p>\n

Gray fabric defect scoring standards:<\/span><\/span><\/p>\n<\/p>\n

Fabric defects are scored on a “four-point scale”<\/span><\/span><\/p>\n<\/p>\n

1. Scoring method <\/span><\/span><\/p>\n

The defect is3 inches<\/span> or below 1 point<\/span><\/span><\/span><\/p>\n

Defects exceeding3<\/span> inches to6<\/span>inch comment2 points<\/span><\/span><\/span><\/p>\n

Defects exceeding6<\/span> inches to9<\/span>inch comment3 points<\/span><\/span><\/span><\/p>\n

Defects exceeding9<\/span>inch comment4 points<\/span><\/span><\/span><\/p>\n<\/p>\n

2<\/span>, continuity defects, each 1<\/span>Code meter4 points:<\/span><\/span><\/span><\/p>\n<\/p>\n

3<\/span>, larger defects (holes, etc.) regardless of size, each 1<\/span> code meter4 points;<\/span><\/span><\/span><\/p>\n<\/p>\n

4<\/span>, rungs, middle edge color, wrong color, insufficient width, wrinkles, poor finishing, etc. , when occurring continuously, each 1<\/span>code<\/span><\/span><\/p>\n

Measurement4 points. <\/span><\/span><\/p>\n<\/p>\n

\nCalculation method in square yards<\/span><\/section>\n<\/p>\n

1<\/span>, each piece of cloth: (commonly used)<\/span><\/span><\/span><\/p>\n

Total number of ratings\u00d736\u00d7100 Rating<\/span><\/p>\n

=number of yards \u00d7 effective width (inches) 100 square yards<\/span><\/span><\/p>\n<\/p>\n

2<\/span>, each order: (whole batch of cloth) <\/span><\/span><\/p>\n

Total score per yard\u00d736\u00d7100 Rating<\/span><\/p>\n

=Total number of yards \u00d7 effective range 100 square yards <\/span><\/p>\n<\/p>\n

\nAcceptance standards (based on 100 square yards) are applicable to Europe, the United States, Japan and other countries<\/span><\/section>\n<\/p>\n

Each piece of cloth<\/span><\/p>\n

1<\/span>Group 15<\/span> points\/100<\/span>square yard<\/span><\/span><\/p>\n

2<\/span>Group 20<\/span> points\/100<\/span>square yard<\/span><\/span><\/p>\n

3<\/span>Group 25<\/span> points\/100<\/span>square yard<\/span><\/span><\/p>\n

4<\/span>group 40<\/span> points\/100<\/span>square yard<\/span><\/span><\/p>\n

5<\/span>group 60<\/span> points\/100<\/span>Square yard<\/span><\/span><\/p>\n<\/p>\n

The current common standard is to use 2<\/span> group, 3<\/span> group, 4-5<\/span> group is not used<\/span><\/span><\/p>\n<\/p>\n

\nDefect scoring criteria<\/span><\/section>\n<\/p>\n

Continuity defects<\/span><\/span><\/p>\n

1<\/span>, continuous and regular defects,1<\/span>Coder4 points<\/span><\/span><\/span><\/p>\n

2<\/span>, continuity3<\/span>codes or above will be treated as substandard products. <\/span><\/p>\n<\/p>\n

Full defects <\/span><\/p>\n

3<\/span>. The following defects are not allowed in qualified products: <\/span><\/span><\/p>\n

A<\/span>\uff0eLength exceeds6<\/span> inch full width defect. <\/span><\/span><\/p>\n

B<\/span>\uff0eSmall full-width defects, 100<\/span> exceeds 5<\/span>. <\/span><\/span><\/p>\n

C<\/span>\uff0e With 100<\/span>code units, each 10<\/span>Severe defects in the code average2<\/span> or more. <\/span><\/span><\/p>\n

D<\/span>\uff0e Cloth head, cloth tail3<\/span> There are serious defects within the code or defects throughout the entire page. <\/span><\/span><\/p>\n

E<\/span>. Lay flatYou can see the edge crepe, Pre-shrunk, corrugated, creased, wrinkled and other defective fabrics. <\/span><\/span><\/p>\n<\/p>\n

4. <\/span>Color:<\/span>Color separation and multi-acceptance3<\/span>LOT<\/span> color, each LOT<\/span> color code number is 500<\/span>codes and above, each LOT<\/span> Color difference between colors according to AATCC<\/span>grey cardLevel 4-5<\/span>. <\/span><\/p>\n<\/p>\n

5<\/span>. The color difference between the middle edge and the head and tail of each piece of cloth cannot be less than 4-5<\/span>level. <\/span><\/p>\n<\/p>\n

6<\/span>. During factory inspection, 6<\/span> inch pieces, numbered and left to the guest. <\/span><\/p>\n<\/p>\n

7<\/span>, guestWhen QC<\/span> comes to inspect the goods, if the color is not straight (Level 4-5<\/span> or below), the item is unqualified <\/span><\/p>\n<\/p>\n

8.<\/span>Code length difference:<\/span>Check that the difference between the actual length and the card label exceeds1%<\/span>, the piece of cloth is unqualified.<\/span><\/p>\n<\/p>\n

9. <\/span>Paragraph length:<\/span>Code length requirement40<\/span>code or above. span><\/p>\n<\/p>\n

10. <\/span>Latitude and arc:<\/span>If it exceeds the following standards, it will be deemed unqualified(Note: When there are partial weft tilts on the entire frame, the score will be based on the part. The weft tilts are not applicable4<\/span> points standard, but should be recorded).<\/span><\/span><\/p>\n<\/p>\n

22.<\/span>Break:<\/span>More than two yarns are broken (any holes, regardless of size, must be evaluated4 points).<\/span><\/span><\/p>\n<\/p>\n

12.<\/span>Density:<\/span>In full inspection, check less3 places, \u00b15%<\/span>, otherwise it will be deemed unqualified, although it does not apply to 4<\/span> points are standard, but must be recorded. <\/span><\/span> <\/p>\n<\/p>\n

13.<\/span>Gram weight:<\/span>During the full inspection process, check less3 places (with temperature and humidity requirements), \u00b15%<\/span>, otherwise it will be rated as unqualified. Although the four-point standard is not applicable, it must be recorded. <\/span><\/span><\/span><\/p>\n<\/p>\n

\nRoll packaging requirements<\/span><\/section>\n<\/p>\n

1<\/span>, no special requirements, approximately 100<\/span>code, no more than 150<\/span> points. <\/span><\/span><\/p>\n

2<\/span>, no special requirements, should be rolled, use paper tube and cannot be damaged during transportation. <\/span><\/span><\/p>\n

<\/div>\n
<\/div>\n

Extended reading: https:\/\/www. china-fire-retardant.com\/post\/9269.html<\/a>
Extended reading: https:\/\/www.china-fire-retardant.com\/post\/9407.html<\/a>
Extended reading: https:\/\/www.alltextile.cn\/product\/product-9-239.html<\/a>
Extended reading:https:\/\/www.alltextile.cn\/product\/product-74-840.html<\/a>
Extended reading: https:\/\/www.tpu-ptfe.com\/post\/3272.html<\/a>
Extended reading:https:\/\/www.brandfabric.net\/uv-cut-fabric\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

American standard inspection and width calculation of gray fabric 1)Test each piece of cloth at least three times. 2)If the width cannot meet the processing requirements, it will b…<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[5],"tags":[46],"class_list":["post-9235","post","type-post","status-publish","format-standard","hentry","category-textile-fabric-news","tag-db"],"_links":{"self":[{"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=\/wp\/v2\/posts\/9235","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=9235"}],"version-history":[{"count":0,"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=\/wp\/v2\/posts\/9235\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=9235"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=9235"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.textile-fabric.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=9235"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}